Made by the FurniMesh team. FurniMesh (furnimesh.com) is our own product, so we benefit when you use it. How we handle that.

Job A · flat image

How to Turn a Photo Into a Lithophane STL

A step-by-step lithophane workflow with starting settings you can copy. If your photo shows an object you want to print in full 3D rather than as a picture, FurniMesh (furnimesh.com), made by our team, handles that case for furniture and home objects.

Published and updated November 22, 2026 · By the Best Image to STL Converter team (FurniMesh)

A lithophane is a thin printed panel whose thickness follows the brightness of a photo: thick where the image is dark, thin where it is bright. Unlit, it looks like a pale embossed slab. Held to a window or a lamp, the photo appears. It is the most popular "image to STL" project, and it needs no 3D modeling at all. This guide uses the free ImageToStl lithophane tool, with notes for 3DPEA.

Pick and prepare the photo

Lithophanes reward strong contrast and simple composition. A face filling half the frame, a pet against a plain wall, or a building against sky all work. Busy group shots and dark, low-contrast photos turn into murk. Before uploading, crop to the final shape (4:3 or square are easiest), convert to grayscale, and raise contrast slightly in any photo editor. Brighten faces a little: skin tends to print darker than expected. Keep the long side at 1200 to 2000 pixels; ImageToStl's lithophane tool resizes anything larger than 2000 pixels anyway.

Close-up of an FDM 3D printer nozzle printing a blue part on a glass bed
Printing upright at fine layer heights gives a lithophane its smooth tonal steps. Photo: Leonhard Lenz, CC BY-SA 4.0, via Wikimedia Commons (source)

Generate the STL

Open the ImageToStl lithophane tool and upload the image. Choose a shape: flat is the simplest, while cylinder, sphere and arc make lamp shades, night-light covers and curved desk displays. Set the depth; ImageToStl suggests around 3 to 4 mm for a lithophane, and its color settings recommend 0.1 mm color layers if your printer can manage it. Make sure the output is a positive lithophane, where dark image areas are thick. If you use 3DPEA image to STL instead, its height map mode with "Invert" gives the same result; set width, height and a basic thickness for the back.

Lithophane starting settings for a 0.4 mm FDM nozzle (our guidance)
SettingStarting valueWhy
Panel size120 x 90 mm for a 4:3 photoLarge enough to show faces and detail; prints in a few hours on most printers
Maximum thickness (darkest areas)3.0 mmImageToStl suggests about 3 to 4 mm of depth
Minimum thickness (brightest areas)0.8 mmTwo perimeters of a 0.4 mm nozzle; thinner can break or gap
Border3 to 5 mm frameStiffens the panel and gives you something to hold
Image resolution1200 to 2000 px on the long sideImageToStl's lithophane tool resizes anything over 2000 px
Layer height0.12 mmFiner layers give smoother tone steps
Infill100%Any infill pattern would show through in the light
OrientationUpright, long edge on the bedPuts the tonal detail in the X/Y plane, where printers are most precise
MaterialWhite or natural PLAColored filament tints and dims the image

A worked example

Take a 1600 x 1200 pixel photo of a dog against a light wall. Set the flat panel to 120 x 90 mm, maximum thickness 3.0 mm, minimum 0.8 mm and a 4 mm border. That gives a panel about 128 x 98 mm with the frame. At 0.12 mm layers, the thickest point is 25 layers deep and the thinnest about 7, so the printer has roughly 18 tonal steps between black and white. That is plenty for a recognizable, smooth image. Raising maximum thickness to 3.6 mm adds about five more steps but makes the darkest areas nearly opaque on a weak light source.

Slicer settings that matter

Print the panel upright, standing on its long edge, with a brim of 5 to 8 mm for stability. Use 100% infill or enough perimeters that the slicer fills the panel solid; any pattern will show through. Slow the outer walls to around 30 mm/s for clean tone transitions. Turn off "ironing" and any fuzzy-skin setting. White PLA is the usual choice; a natural or translucent white gives brighter highlights. Expect a 120 mm panel at 0.12 mm layers to take several hours.

Lighting and display

Lithophanes need light from behind. A daylight window works for a test. For display, use an LED strip or puck in a printed frame, kept a few centimeters behind the panel so the light spreads evenly. Warm white light softens the image; cool white makes it crisper. Curved lithophanes look best around a cylindrical LED lamp.

Common problems

  • Image is too dark everywhere: maximum thickness is too high for your light. Reduce to 2.6 to 3.0 mm.
  • Bright areas have holes: minimum thickness is below what your nozzle can print. Raise it to 0.8 mm.
  • Visible stripes: layer height too coarse, or the panel was printed lying flat. Print upright at 0.12 mm.
  • Panel wobbles while printing: add a brim or a thicker frame along the bottom edge.

When a lithophane isn't what you want

A lithophane only ever reproduces the picture as a picture. If the photo shows an object, say a chair, and you want to print the chair itself, you need a different tool. Our photo to printable model guide covers that, using FurniMesh (furnimesh.com), our own product, to generate a 3D model from the photo before converting it to STL. For signs and logos that should look sharp in normal light, see PNG to STL for logos.

Curved and cylindrical lithophanes

Curved shapes need slightly different numbers. A cylinder for a lamp shade should be at least 80 mm in diameter, so the image doesn't wrap too tightly to read, and the seam should sit at the back. Keep the same 0.8 mm minimum and 3.0 mm maximum thickness, and add a 3 to 4 mm solid ring at the top and bottom for strength and to seat the shade on its base. Print cylinders standing up, with no supports needed. An arc, which bends the panel gently, is the easiest curved form for a first attempt: it stands on its own without a frame and looks good with a single LED behind it.

Keep going

The other guides on this site, each on a separate step of the image-to-print process.